| • Wireless Systems |
| > 4-Up DX200 System |
| | - | 1: Base station with 2 atennas |
| |
| > AC40 Battery Charger |
| | - | 0: Battery Charger for the BP200 Beltpac battery, 4-port quick charger with adapter |
| |
| > Antenna kit1 |
| | - | 0: Remote Base Station antenna with 6' cable |
| |
| > Antenna kit2 |
| | - | 0: Remote Base Station Antenna with 30' Cable |
| |
| > BAT40 |
| | - | 0: Battery for the BP200 Beltpac, Lithium-ion Rechargeable |
| |
| > BP200 Beltpac |
| | - | 2: Belt pac with 2 batteries, a pouch, and HS12 Headset |
| |
| > BS200 Base Station |
| | - | 1: Base Station with power supply, 2 antennas, 1 HS11 Headset |
| |
| > HS12 Headset |
| | - | 0: Headset, lightweight, single earpiece with electret mic |
| |
| |
| • Main Stations and Power Supplies |
| > LS-2 Speaker Station-listen only |
| | - | THe LS-2 is ideally suited for dressing room and green room locations where talkback is not required. |
| |
| > LS-3R Talkback Station |
| | - | LS-3 Talkback stations operate in three modes: Press-to-talk; hands-free simulatneous talk/listen; or as a headset/handset station. |
| |
| > MS-200 Two-circuit Master Station |
| | - | The MS-200 is a full-featured Two-circuit Master Station combiningh an outboard power supply with the facilities to control two independent communications circuits |
| |
| > MSM-1 Stage Manager Station |
| | - | The MSM-1 is a multipurpose 2-curcuit station, one or more of which can be used in a system. |
| |
| > MSM-2 Two-Circuit Add-On |
| | - | This unit is connected to an MS-200 or an MSM-1 with the cable supplied and adds two additional communicatiosn circuits. |
| |
| > MSM-3 Four-Circuit Add-On |
| | - | This unit is connected to an MS-200 or MSM-1 with the cable supplied, and adss four additional communications circuits. |
| |
| > PS-1B Basic Power Supply |
| | - | THis version of the PS Series power supplies is intended for use where the system is being controlled by other stations, or where additional supply current needs to be added in large or widely spread out systems. |
| |
| > PS-2 Power Supply |
| | - | the PS-2 is the successor to the PS-1A/L and is a highly regulated 24VDC 2Amp power supply capable of supporting 66 BP-1 belt packs with all their signals lights constantly lit. |
| |
| > PS-3 Power Supply |
| | - | The PS-3 will power your system from a pair of 12-Volt batteries wired in series to provide 24VDC. |
| |
| > RSM-1 Remote Stage Manager Station |
| | - | The RSM-1 has all the features of the RSM-2 exept for the loudspeaker. |
| |
| > RSM-2 Remote Stage Manager Station |
| | - | The RSM-2 probides communications with two circuits without tying those two circuts together. |
| |
| |
| • Beltpacks and Headset Stations |
| > BP-1 Single-circuit Beltpack |
| | - | BP series 'belt packs' combine wide bandwidth, superior sidetone rejection and low current consumption to provide optimum performance at moderate cost. Cotrols are shaped for easy touch identification. The extruded aluminum case and high impact end bezels provide industryleading durability excessive weight. |
| |
| > BP-1S/L Single-circuit with A/B Switch |
| | - | BP series 'belt packs' combine wide bandwidth, superior sidetone rejection and low current consumption to provide optimum performance at moderate cost. Cotrols are shaped for easy touch identification. The extruded aluminum case and high impact end bezels provide industryleading durability excessive weight. |
| |
| > BP-2 Two-circuit Beltpack |
| | - | BP series 'belt packs' combine wide bandwidth, superior sidetone rejection and low current consumption to provide optimum performance at moderate cost. Cotrols are shaped for easy touch identification. The extruded aluminum case and high impact end bezels provide industryleading durability excessive weight. |
| |
| > BP-2B Two-channel w/Binaural Feed |
| | - | BP series 'belt packs' combine wide bandwidth, superior sidetone rejection and low current consumption to provide optimum performance at moderate cost. Cotrols are shaped for easy touch identification. The extruded aluminum case and high impact end bezels provide industryleading durability excessive weight. |
| |
| > HS-1/T Fixed Headset Station |
| | - | HS series headset stations perform the same functions as a 'belt pack' but are packaged as flush-mount, table top or rack-mount configurations. Multi-circuit versions provide a rotary switch. Selct up to 9 circuits |
| |
| |
| • Headsets and Handsets |
| > DMH220 Double Ear |
| | - | Series 200 headsets have been famous for years for their durability, comfort, performance and moderate cost. With only two moving parts there is little to go wrong with these workhorses. Popular wherever reliability is at a premium, they are also compatible with intercom systems from other manufacturers and versions are available for custom applications. The soft, comfortable muffs are removable, replaceable, and can be washed in a mild detergent solution. The SMH210 and DMH220 are fitted with premium quality Neutrik XLR-type connectors. |
| |
| > DMH320 Double Ear |
| | - | Series 300 Headsets offer optimum value while also providing several unique features including a gooseneck microphone boom which, in addition to swinging up-and-down, permits the microphone to be placed in a wide range of positions. The soft, comfortable muffs can be removed and cleaned. These headsets are compatible with most other manufacturers intercom systems. |
| |
| > SMH110 |
| | - | The SMH110 and SMH111 are identical in construction differing only in the microphone fitted. The SMH110 has a magnetic microphone, compatible with dynamic microphones. The SMH111 has an electret condenser microphone. The unique design results in no earphone pad either on or in the ear. The 'ear loop' goes around the ear and holds the transducer at the ear opening. The boom swivels up, down, in and out adjusts back to front. At the point where most lightweights fail, the boom snapped back in. Great Value! |
| |
| > SMH111 |
| | - | The SMH110 and SMH111 are identical in construction differing only in the microphone fitted. The SMH110 has a magnetic microphone, compatible with dynamic microphones. The SMH111 has an electret condenser microphone. The unique design results in no earphone pad either on or in the ear. The 'ear loop' goes around the ear and holds the transducer at the ear opening. The boom swivels up, down, in and out adjusts back to front. At the point where most lightweights fail, the boom snapped back in. Great Value! |
| |
| > SMH210 Single Ear |
| | - | Series 200 headsets have been famous for years for their durability, comfort, performance and moderate cost. With only two moving parts there is little to go wrong with these workhorses. Popular wherever reliability is at a premium, they are also compatible with intercom systems from other manufacturers and versions are available for custom applications. The soft, comfortable muffs are removable, replaceable, and can be washed in a mild detergent solution. The SMH210 and DMH220 are fitted with premium quality Neutrik XLR-type connectors. |
| |
| > SMH310 Single Ear |
| | - | Series 300 Headsets offer optimum value while also providing several unique features including a gooseneck microphone boom which, in addition to swinging up-and-down, permits the microphone to be placed in a wide range of positions. The soft, comfortable muffs can be removed and cleaned. These headsets are compatible with most other manufacturers intercom systems. |
| |
| |
| • Accessories |
| > AD903 Input/Output Adapter |
| | - | The AD903 is used to inject a mic or line level audio program onto the intercom line; to feed the intercom audio out to an amplifier, mixer or recorder input - or both of these functions. The AD903 also provides a simple means of inter facing two incompativle intercom systems. |
| |
| > AD913 Transceiver Interface |
| | - | The Ad913 permits communications between your Production Intercom cabled intercom system and any number of standard, simplex transceivers is dedicated as 'base' and connected via its accessory mic/spkr jacks to the Ad913. The AD913 is connected to the intercom system as if it were another belt pack. Transmissions from other transceivers on the same frequency as the 'base' will then be heard on the cabled stations. Cabled stations may transmit to the remote transceivers by simply pressing and holding their signal buttons. Production Intercom can provide reasonably priced cables for connecting most transceivers to the AD913. |
| |
| > BA905 Power Supply Link |
| | - | The BA905 is a female-to female XLR gender adapters for linking multiple power supplies using standard microphone cables. |
| |
| > Blazon/3 Call Light |
| | - | Blazon/3 supplements any intercom station call light with a bright visual signal and an switchable loud audible signal. The low-current strobe is roughly the equivalent of three belt packs allowing the Blazon/3 to be powered by the intercom supply alone. The audible alert may be switched from constant to pulsing to off. Triggered by any signal lamp button on the same circuit, an internal timer sustains the signal for 3 seconds. Loop-through male and female XLR-type jacks on the back panel allow the Blazon/3 to be connected to the system exactly as is a beltpack. |
| |
| > LI906 Line Terminator |
| | - | The Li906 provides the necessary end-of-line terminations for commencing a new communications circuit from an already in-use power supply. |
| |
| > OG904 Override Module |
| | - | LS-series loudspeaker stations contain a circuit that responds to a signal will force an LS loudspeaker staton into predetermined mode, regardless of the positions of its front panel controls. it will raise or lower volume, shift from Off or Talk to Listen and several other choices, selected by adding or removing links from the LS circuit board. Applications include restoring volume at a dressing room speaker station that has been turned down, or muting one LS station to avoid feedback when another close-by LS station is being used. The OG904 is a circuit card which can be installed in an MS-200, an MSM-1, a BP-1 beltpack, or even another LS speaker station. |
| |
| |